Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be major accidents in mins, and there are numerous accidents including forklifts.

Case 1: The forklift cargo obstructed the vehicle driver's view, and the person in front can not be located, leading to a rolling mishap.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the staff members utilized their body weight as the weight, which almost caused casualties.
Instance 3: The width of the forklift freight exceeds the allowable size of the path and holds on the roadside shelf, which almost creates an accident.
Case 4: Forklift is speeding up and rolls over throughout a turn.
Case 5: The forklift driver did not discover the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the workers illegally, the forklift vehicle driver does not wear the seat belt, the forklift lifter drops and the driver is squashed when the forklift surrender.
Situation 7: The forklift driver did not wear a seat belt and dropped from the lorry when it surrendered and was squashed.
Forklift operation need to take notice of these matters ：.

Begin.
1. Prior to starting, observe the environments, and after confirming that there are no obstacles that impede the safety of driving, honk the horn initially and after that start.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) scale have to be risk-free before beginning.
3. When the forklift starts with a load, the motorist needs to initially confirm that the load is secure and dependable.
4. The begin should be sluggish and constant.

Driving.
1. When driving, the height between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not lift the fork expensive when driving. When entering and leaving the job site or while driving, beware that there will certainly be no challenges overhead. When the load is taking a trip, the fork needs to not be raised expensive, which will affect the security of the forklift. .
3. After discharging, the fork should be lowered to the typical driving setting before driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal should be issued first. High-speed sharp turns are forbidden. High-speed doglegs will cause the automobile to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to switch off the flame and slide, and it is restricted to brake suddenly while driving with tons unless there are special scenarios.
6. When the forklift is running, it has to follow the web traffic rules in the factory and must keep a particular safety distance from the vehicle in front. .
7. When the forklift is running, the lots needs to be in the most affordable placement that does not prevent the driving, and the gantry must be properly tilted back. The lots shall not be increased other than when stacking or loading. .
8. The height of the tons have to not obstruct the driver's sight. In special scenarios, when the item impacts the forward vision, drive at a reduced speed when turning around.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when entering the manufacturing workshop location. .
11. When the forklift is raised, raised or driven, it is forbidden for employees to depend on the fork to hold things and play a stabilizing duty. .
12. If troubles are located, they will certainly be fixed and reported in a timely way, and they will never ever operate with illnesses or hide them.

loading and unloading.
1. When fork-loading items, the range in between both forks must be readjusted as required to make the load of both forks well balanced and not manipulated, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or make use of a fork top or pull. In special circumstances, security warning signs must be set up to remind surrounding pedestrians. .
3. In the process of packing and unloading items, the forklift should be braked with the brake. .
4. The rate of the vehicle need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork idea should not touch other products or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to make use of forks to raise employees to engage in high-altitude procedures to avoid high-altitude falling crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you Stand-on Electric Pallet Stacker should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake switch.
3. The engine Electric Forklift Truck for Warehouse is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift employees bring the goods and move on, if they come across huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844